8 questions Basic

### 13 - The Basic Hydraulics and Pump Performance Course

This course test contains 8 questions and can be retaken at any time.

You must answer all questions correctly to pass the test and complete the course.

Question 1 of 8 Basic

Identify the correct formula for calculating pump efficiency.

Question 2 of 8 Basic

Which of the following items are built-in in some motors and can stop the motor if it exceeds a preset temperature:

Question 3 of 8 Basic

How can friction loss in a system be minimised?

Question 4 of 8 Basic

Friction loss is dependent on the [xxxxxxxx] of the fluid.

Question 5 of 8 Basic

Which of the following parameters is not used for calculating pump efficiency?

Question 6 of 8 Basic

Identify the true statement.

Question 7 of 8 Basic

How is the relationship between these three factors described in an equation?

Question 8 of 8 Basic

Which of the following is one correct method to avoid cavitation?

Question 8 of 8 Basic

# Test results

Congratulations. You have passed the test and completed the 13 - The Basic Hydraulics and Pump Performance Course

### How would you rate this course?

You are welcome to add your rating of this course. Remember that you have to be logged in before you take the test to be able to give your rating.

Sorry. You did not pass the 13 - The Basic Hydraulics and Pump Performance Course test this time

### How would you rate this course?

You are welcome to add your rating of this course. Remember that you have to be logged in before you take the test to be able to give your rating.

Q: Identify the correct formula for calculating pump efficiency.
A: (P1 × Q)/(c × H)
02: (p x H × Q)/(c × P1)
03: (H × P1)/(c × Q)
Q: Identify the correct formula for calculating pump efficiency.
A: (p x H × Q)/(c × P1)
Q: Identify the correct formula for calculating pump efficiency.
A: (H × P1)/(c × Q)
01: (P1 × Q)/(c × H)
02: (p x H × Q)/(c × P1)
Q: Which of the following items are built-in in some motors and can stop the motor if it exceeds a preset temperature:
A: Temperature sensors
Q: Which of the following items are built-in in some motors and can stop the motor if it exceeds a preset temperature:
A: Signal wire
01: Temperature sensors
03: Insulation system
Q: Which of the following items are built-in in some motors and can stop the motor if it exceeds a preset temperature:
A: Insulation system
01: Temperature sensors
02: Signal wire
Q: How can friction loss in a system be minimised?
A: By increasing the pipe diameter
Q: How can friction loss in a system be minimised?
A: By using 2 smaller pumps instead of one bigger pump
01: By increasing the pipe diameter
03: By adding a Tee to the piping system
Q: How can friction loss in a system be minimised?
A: By adding a Tee to the piping system
01: By increasing the pipe diameter
02: By using 2 smaller pumps instead of one bigger pump
Q: Friction loss is dependent on the [xxxxxxxx] of the fluid.
A: Viscosity
02: Velocity
03: Volume
Q: Friction loss is dependent on the [xxxxxxxx] of the fluid.
A: Velocity
Q: Friction loss is dependent on the [xxxxxxxx] of the fluid.
A: Volume
01: Viscosity
02: Velocity
Q: Which of the following parameters is not used for calculating pump efficiency?
A: Flow
02: Time
03: Pressure
04: Power Consumption
Q: Which of the following parameters is not used for calculating pump efficiency?
A: Time
Q: Which of the following parameters is not used for calculating pump efficiency?
A: Pressure
01: Flow
02: Time
04: Power Consumption
Q: Which of the following parameters is not used for calculating pump efficiency?
A: Power Consumption
01: Flow
02: Time
03: Pressure
Q: Identify the true statement.
A: In deep-well pumps, you should check whether the pressure gauge is installed directly at the pump discharge.
01: In deep-well pumps, you should check whether the pressure gauge is installed directly at the pump discharge. Your answer
02: Online monitoring equipment does not check if a parameter has changed or exceeded a preset limit.
03: If all the parameters are recorded immediately after the pump has been installed, you can use them as benchmark against future data.
Q: Identify the true statement.
A: Online monitoring equipment does not check if a parameter has changed or exceeded a preset limit.
01: In deep-well pumps, you should check whether the pressure gauge is installed directly at the pump discharge.
02: Online monitoring equipment does not check if a parameter has changed or exceeded a preset limit. Your answer
03: If all the parameters are recorded immediately after the pump has been installed, you can use them as benchmark against future data.
Q: Identify the true statement.
A: If all the parameters are recorded immediately after the pump has been installed, you can use them as benchmark against future data.
Q: How is the relationship between these three factors described in an equation?
A: P = Q x H x c
Q: How is the relationship between these three factors described in an equation?
A: Q = H x P x c
01: P = Q x H x c
03: P = Q/H x c
Q: How is the relationship between these three factors described in an equation?
A: P = Q/H x c
01: P = Q x H x c
02: Q = H x P x c