What happens if the water level in the well drops below the inlet?
In addition to limiting the current draw from the mains during start-up of the pump, how does the soft-start functionality benefit operation?
What is the benefit of a slow increase in speed?
Why must the pump unit be installed below the dynamic water table?
Which of these isn’t a key dry-run protection benefit for the installer?
What is a key installer benefit of the voltage protection in SQ/SQE?
Which submersible pump was replaced with a Grundfos SQ?
What is the most commonly used starting method for motors in 4” conventional pumps?
How long did it take to replace the pump with a Grundfos SQ?
Résultats de l’évaluation
Q: What happens if the water level in the well drops below the inlet?
A: The motor power consumption drops
Q: What happens if the water level in the well drops below the inlet?
A: The motor power consumption stays the same
Q: What happens if the water level in the well drops below the inlet?
A: The motor power consumption increases
Q: In addition to limiting the current draw from the mains during start-up of the pump, how does the soft-start functionality benefit operation?
A: Soft start reduces over-pressure in your piping.
Q: In addition to limiting the current draw from the mains during start-up of the pump, how does the soft-start functionality benefit operation?
A: It reduces the occurrence of water hammer in the pipes and minimises wear during start-up.
Q: In addition to limiting the current draw from the mains during start-up of the pump, how does the soft-start functionality benefit operation?
A: Soft start prevents the motor from getting warm.
Q: What is the benefit of a slow increase in speed?
A: It keeps the motor current low
Q: What is the benefit of a slow increase in speed?
A: It keeps pump movements at a minimum
Q: What is the benefit of a slow increase in speed?
A: It removes the need for motor contactors
Q: Why must the pump unit be installed below the dynamic water table?
A: So you are sure to minimise your power bill.
Q: Why must the pump unit be installed below the dynamic water table?
A: To avoid the risk of dry-running during operation.
Q: Why must the pump unit be installed below the dynamic water table?
A: To maintain a stable pressure in the system.
Q: Is the SQE pump able to provide constant pressure?
A: No.
Q: Is the SQE pump able to provide constant pressure?
A: Yes.
Q: Which of these isn’t a key dry-run protection benefit for the installer?
A: He can avoid costly callbacks
Q: Which of these isn’t a key dry-run protection benefit for the installer?
A: He doesn’t have to worry about additional components
Q: Which of these isn’t a key dry-run protection benefit for the installer?
A: He doesn’t have to worry about water bursts
Q: What is a key installer benefit of the voltage protection in SQ/SQE?
A: Steady water supply
Q: What is a key installer benefit of the voltage protection in SQ/SQE?
A: Faster installation
Q: What is a key installer benefit of the voltage protection in SQ/SQE?
A: Fewer service visits
Q: Which submersible pump was replaced with a Grundfos SQ?
A: A 4” submersible pump
Q: Which submersible pump was replaced with a Grundfos SQ?
A: A 3” submersible pump
Q: Which submersible pump was replaced with a Grundfos SQ?
A: A 5” submersible pump
Q: What is the most commonly used starting method for motors in 4” conventional pumps?
A: Direct on line
Q: What is the most commonly used starting method for motors in 4” conventional pumps?
A: Star delta starters
Q: What is the most commonly used starting method for motors in 4” conventional pumps?
A: Auto transformer
Q: How long did it take to replace the pump with a Grundfos SQ?
A: 30 minutes
Q: How long did it take to replace the pump with a Grundfos SQ?
A: 60 minutes
Q: How long did it take to replace the pump with a Grundfos SQ?
A: 90 minutes